Fiber cement FAQ
Find answers by topic, from choosing a board to preparing a quote. Confirm installation and performance requirements for the exact product and assembly.
Product selection
What is fiber cement cladding?
Fiber cement cladding is a cement-based composite board used as an exterior finish in suitable building systems. Ecobetek also offers facade panels, shingles, decking and backer boards. Each product has its own application and installation requirements.
How do Click cladding, lap cladding and facade panels differ?
Click planks connect through an interlocking profile. Lap planks overlap in courses. Larger panels suit broader layouts and may use different supports, fixings and joints.
How do I confirm a board is suitable for my project?
Share the application, profile, dimensions, thickness, finish, substrate and proposed fixing method. Ask which drawings, installation instructions and product-specific reports are available for that combination.
How do I calculate how many boards I need?
Use the installed cover width or shingle exposure for the selected profile. Allow for cuts, openings, joints and waste. Confirm the effective coverage before converting your area into an order quantity.
Finishes and colors
Which products are factory-coated?
Coated facade panels, Click cladding, lap cladding and shingle siding are factory-coated. Brushed and polished color-through panels have color throughout the board and require no surface painting.
Can colors vary between batches?
Small differences can occur. Approve a physical sample and discuss batch planning before ordering if color consistency is important.
Do cut edges need treatment?
Factory-coated boards may need cut-edge treatment. Confirm the requirements for your product and finish before processing the boards.
Substrates, fixings and joints
Can I fix the boards to timber or light-gauge steel?
Either may be suitable depending on the board and system. Large facade panels may need a dedicated metal subframe. Confirm the substrate and fasteners, including any need for pre-drilling or rivets, with the product instructions.
Who specifies the cavity, ventilation and drainage?
Follow the project design and local requirements for cavity depth, ventilation, drainage and weatherproofing. Ask Ecobetek to confirm product-specific limits.
Which trims and joint treatments should I use?
Confirm compatible starter, corner, end and opening trims for the board. Coordinate window and door flashings with the project design. Use sealant where the detail calls for it and keep designed drainage and ventilation paths open.
Can shingle siding use the same installation details as lap cladding?
Confirm the shingle starter, fixings, clearances and exposure for the selected profile. Plan level courses and joint staggering, and support cut pieces at corners and openings.
How is fiber cement decking fixed?
Square-edge boards are screw-fixed. Grooved-edge boards use matching clips. Confirm fasteners for the support material and check the support spacing and board gaps for your profile and design loads.
Where can fiber cement backer board be used?
Confirm the exact board and assembly before specifying wall, ceiling, floor or wet-area use. Backer board usually sits beneath a finish. Joint materials, fixings, membranes and waterproofing depend on the build-up and exposure.
Handling and maintenance
What should I check before storing or cutting boards?
Store boards flat, dry and evenly supported. Lift them clear of the stack and follow the supplier’s packaging instructions. Use the specified tools, suitable dust extraction and site safety controls. Clean up with a suitable vacuum or wet method.
Can I pressure-wash fiber cement?
Start with clean water and a soft cloth or brush. Test a mild detergent only if suitable for the finish. Use high-pressure cleaning only if the supplier permits it.
What should I do if I see white marks?
Mineral deposits or efflorescence are possible causes. Record the affected area, batch and storage conditions. Test gentle cleaning in a small area and avoid unapproved acids, sanding or repainting. If marks persist, send photos and installation details to the supplier.
Samples, quotes and export orders
Can I request samples or custom dimensions?
Send the profile, thickness, finish, color and delivery destination for samples. Custom sizes, colors and profiles depend on the product, tooling, order quantity and production schedule.
What are the minimum order quantity and lead time?
Minimum quantities and production lead times depend on the product, finish, color, quantity and tooling. Confirm both in the quotation.
What should I include in a quote request?
Include the profile, intended use, dimensions, thickness, finish, color reference and substrate. Add quantity, order frequency, destination country or port, target date, sample needs and any packing or labeling requirements. Ask for pallet dimensions and gross weight for your order.
Get a quote for your project
Share the board, finish, quantity and destination so we can review your requirements.
